WiZ Smart Plug
Vendor ID:
4107
Product ID:
8976
Seen:
0 times
No Binding
CSA Certification:
What This Device Can Do
0% of features
| Controls | ||
|---|---|---|
| 💡 On/Off control | v1.0 | ✕ |
| 🔆 Brightness dimming | v1.0 | ✕ |
| 🎨 Color temperature | v1.0 | ✕ |
| 🌈 Full color (RGB) | v1.0 | ✕ |
| 🌀 Fan speed control | v1.0 | ✕ |
| 🪟 Blinds/shades control | v1.0 | ✕ |
| 🔒 Lock/unlock | v1.0 | ✕ |
| 🌡️ Temperature setpoint | v1.0 | ✕ |
| 💧 Pump control | v1.0 | ✕ |
| 🚰 Valve control | v1.3 | ✕ |
| Sensors | ||
|---|---|---|
| 🌡️ Temperature sensor | v1.0 | ✕ |
| 💧 Humidity sensor | v1.0 | ✕ |
| 👁️ Occupancy/motion sensor | v1.0 | ✕ |
| ☀️ Light level sensor | v1.0 | ✕ |
| 🚪 Open/close sensor | v1.0 | ✕ |
| 📊 Pressure sensor | v1.0 | ✕ |
| 🌊 Flow sensor | v1.0 | ✕ |
| 🌿 Air quality sensor | v1.2 | ✕ |
| 🔥 Smoke detector | v1.2 | ✕ |
| ⚠️ Carbon monoxide detector | v1.2 | ✕ |
| Automation & Scenes | ||
|---|---|---|
| 🎬 Scenes & presets | v1.4 | ✕ |
| 👥 Group control | v1.0 | ✕ |
| 🔗 Device-to-device control | v1.0 | ✕ |
| ▶️ Automation actions | v1.0 | ✕ |
| 🎚️ Operating modes | v1.0 | ✕ |
| ⏰ Scheduling | v1.0 | ✕ |
| 👁️ Responds to occupancy | v1.0 | ✕ |
| Info & Monitoring | ||
|---|---|---|
| ⚡ Energy monitoring | v1.3 | ✕ |
| 🔋 Battery status | v1.0 | ✕ |
| 📊 Device diagnostics | v1.0 | ✕ |
| ⬇️ Firmware updates | v1.0 | ✕ |
| Comfort & Climate | ||
|---|---|---|
| 🔥 Heating | v1.0 | ✕ |
| ❄️ Cooling | v1.0 | ✕ |
| 🔄 Auto heat/cool | v1.0 | ✕ |
| 📌 Temperature presets | v1.0 | ✕ |
| 💧 Humidity control | v1.0 | ✕ |
| 🌿 Air purification | v1.2 | ✕ |
| Security | ||
|---|---|---|
| 🔢 PIN code access | v1.0 | ✕ |
| 💳 RFID/card access | v1.0 | ✕ |
| 👤 User management | v1.0 | ✕ |
| 🔔 Alarm/siren | ✕ | |
| Media & Entertainment | ||
|---|---|---|
| ▶️ Media playback | v1.0 | ✕ |
| 🔊 Volume control | ✕ | |
| 📺 Channel selection | v1.0 | ✕ |
| 🔌 Input selection | v1.0 | ✕ |
| 📲 Casting/streaming | v1.0 | ✕ |
Not available:
Device-to-device control, Energy monitoring
Setup & Reset Info
▼
Setup:
Power Cycle
Reset:
Standard
Additional Steps:
Press and hold the button on your plug for around 10s, until the LED indicator starts blinking. This indicates commissioning mode. While it blinks, continue the setup in your commissioner app.