The Meross Smart Wi-Fi Thermostat is a Matter device (Vendor 0x1345, Product 0xE002) with 4 endpoints.

Last updated 12 Jun 2026

Smart Wi-Fi Thermostat (PID 0xE002)

★ ★ ★ ☆ ☆ (60%)

Meross

Vendor ID: 4933

Product ID: 57346

Seen: 37 times

No Binding Wifi

CSA Certification:

Certified Apr 23, 2025 CSA25213MAT45413-24 v9.3.2

Links: 🛟 Support 📖 Manual

What This Device Can Do

Climate

★ ★ ★ ☆ ☆ 36% of features

Controls
▶ 🌡️ Temperature setpoint	v1.0	✓
Thermostat What you can do: ✓ Raise or lower the target temperature ✓ Raise or lower the target temperature ✕ Set weekly schedule optional ✕ Get weekly schedule optional ✕ Add thermostat suggestion response optional ✕ Clear weekly schedule optional ✕ Set active schedule request optional ✕ Set active preset request optional ✕ Add thermostat suggestion optional ✕ Remove thermostat suggestion optional ✕ Atomic response optional ✕ Atomic request optional Information available: ✓ Current room temperature ✕ Outdoor temperature optional ✕ Occupancy optional ✓ Abs min heat setpoint limit ✓ Abs max heat setpoint limit ✓ Abs min cool setpoint limit ✓ Abs max cool setpoint limit ✕ Pi cooling demand optional ✕ Pi heating demand optional ✕ Hvac system type configuration optional ✕ Local temperature calibration optional ✓ Target cooling temperature ✓ Target heating temperature ✕ Unoccupied cooling setpoint optional ✕ Unoccupied heating setpoint optional ✓ Min heat setpoint limit ✓ Max heat setpoint limit ✓ Min cool setpoint limit ✓ Max cool setpoint limit ✓ Min setpoint dead band ✕ Remote sensing optional ✓ Control sequence of operation ✓ Current mode (heat/cool/auto/off) ✕ Thermostat running mode optional ✕ Start of week optional ✕ Number of weekly transitions optional ✕ Number of daily transitions optional ✕ Temperature setpoint hold optional ✕ Temperature setpoint hold duration optional ✕ Thermostat programming operation mode optional ✕ Thermostat running state optional ✕ Setpoint change source optional ✕ Setpoint change amount optional ✕ Setpoint change source timestamp optional ✕ Occupied setback optional ✕ Occupied setback min optional ✕ Occupied setback max optional ✕ Unoccupied setback optional ✕ Unoccupied setback min optional ✕ Unoccupied setback max optional ✕ Emergency heat delta optional ✕ Ac type optional ✕ Ac capacity optional ✕ Ac refrigerant type optional ✕ Ac compressor type optional ✕ Ac error code optional ✕ Ac louver position optional ✕ Ac coil temperature optional ✕ Ac capacityformat optional ✕ Preset types optional ✕ Schedule types optional ✕ Number of presets optional ✕ Number of schedules optional ✕ Number of schedule transitions optional ✕ Number of schedule transition per day optional ✕ Active preset handle optional ✕ Active schedule handle optional ✕ Presets optional ✕ Schedules optional ✕ Setpoint hold expiry timestamp optional ✕ Max thermostat suggestions optional ✕ Thermostat suggestions optional ✕ Current thermostat suggestion optional ✕ Thermostat suggestion not following reason optional Enabled features: Heating
🌀 Fan speed control	v1.1	✕

Sensors
▶ 🌡️ Temperature sensor	v1.0	✓
Temperature Measurement Information available: ✓ Current temperature reading ✓ Minimum measurable temperature ✓ Maximum measurable temperature ✕ Tolerance optional
▶ 💧 Humidity sensor	v1.0	✓
Relative Humidity Measurement Information available: ✓ Current humidity reading ✓ Minimum measurable humidity ✓ Maximum measurable humidity ✕ Tolerance

Automation & Scenes
🎬 Scenes & presets	v1.3	✕
⏰ Scheduling	v1.0	✕

Comfort & Climate
▶ 🔥 Heating	v1.0	✓
Thermostat What you can do: ✓ Setpoint raise lower ✓ Get weekly schedule response ✕ Set weekly schedule optional ✕ Get weekly schedule optional ✕ Add thermostat suggestion response optional ✕ Clear weekly schedule optional ✕ Set active schedule request optional ✕ Set active preset request optional ✕ Add thermostat suggestion optional ✕ Remove thermostat suggestion optional ✕ Atomic response optional ✕ Atomic request optional Information available: ✓ Current room temperature ✕ Outdoor temperature optional ✕ Occupancy optional ✓ Abs min heat setpoint limit ✓ Abs max heat setpoint limit ✓ Abs min cool setpoint limit ✓ Abs max cool setpoint limit ✕ Pi cooling demand optional ✕ Pi heating demand optional ✕ Hvac system type configuration optional ✕ Local temperature calibration optional ✓ Occupied cooling setpoint ✓ Target heating temperature ✕ Unoccupied cooling setpoint optional ✕ Unoccupied heating setpoint optional ✓ Min heat setpoint limit ✓ Max heat setpoint limit ✓ Min cool setpoint limit ✓ Max cool setpoint limit ✓ Min setpoint dead band ✕ Remote sensing optional ✓ Control sequence of operation ✓ System mode ✕ Thermostat running mode optional ✕ Start of week optional ✕ Number of weekly transitions optional ✕ Number of daily transitions optional ✕ Temperature setpoint hold optional ✕ Temperature setpoint hold duration optional ✕ Thermostat programming operation mode optional ✕ Thermostat running state optional ✕ Setpoint change source optional ✕ Setpoint change amount optional ✕ Setpoint change source timestamp optional ✕ Occupied setback optional ✕ Occupied setback min optional ✕ Occupied setback max optional ✕ Unoccupied setback optional ✕ Unoccupied setback min optional ✕ Unoccupied setback max optional ✕ Emergency heat delta optional ✕ Ac type optional ✕ Ac capacity optional ✕ Ac refrigerant type optional ✕ Ac compressor type optional ✕ Ac error code optional ✕ Ac louver position optional ✕ Ac coil temperature optional ✕ Ac capacityformat optional ✕ Preset types optional ✕ Schedule types optional ✕ Number of presets optional ✕ Number of schedules optional ✕ Number of schedule transitions optional ✕ Number of schedule transition per day optional ✕ Active preset handle optional ✕ Active schedule handle optional ✕ Presets optional ✕ Schedules optional ✕ Setpoint hold expiry timestamp optional ✕ Max thermostat suggestions optional ✕ Thermostat suggestions optional ✕ Current thermostat suggestion optional ✕ Thermostat suggestion not following reason optional Enabled features: Heating
❄️ Cooling	v1.0	✕
🔄 Auto heat/cool	v1.0	✕
📌 Temperature presets	v1.0	✕
💧 Humidity control	v1.1	✕

⚠ Not available: Scheduling

Setup & Reset Info

▼

Setup: Power Cycle Reset: Standard

Additional Steps:

5,,0x01&0x02

Technical Details For developers

▼

Device Compatibility

Can provide data to: These devices have client clusters that can read from or control this device's server clusters

Thermostat (3 devices)

Aqara Climate Sensor W100 (Aqara) Eve Thermo Control (Eve) Touchscreen Switch S100 (Aqara)

Relative Humidity Measurement (1 device)

Touchscreen Switch S100 (Aqara)

Temperature Measurement (3 devices)

Eve Thermo (Eve) Eve Thermo (Eve) Touchscreen Switch S100 (Aqara)

Spec Compliance & Feature Analysis

Comparing this device's clusters against Matter specification requirements. Shows what's implemented, what's missing, and bonus features. Note: Legacy clusters (e.g., Scenes) count as compliant when replaced by newer equivalents (Scenes Management).

Thermostat Matter 1.0 Compliant

★ ★ ★ ☆ ☆ Feature Score:

60%

Optional Not Implemented 5

Per the Matter spec, these clusters are optional. The device is compliant without them.

Energy Preference Fan Control (client) Temperature Measurement (client) Relative Humidity Measurement (client) Occupancy Sensing (client)

Bonus Features Implemented 2

Groups Thermostat User Interface Configuration

Extra (Beyond Spec) 1

Descriptor

2/2 required | 2/7 optional

Humidity Sensor Matter 1.0 Compliant

★ ★ ★ ☆ ☆ Feature Score:

60%

Extra (Beyond Spec) 1

Descriptor

2/2 required | 0/0 optional

Temperature Sensor Matter 1.0 Compliant

★ ★ ★ ☆ ☆ Feature Score:

60%

Extra (Beyond Spec) 1

Descriptor

2/2 required | 0/0 optional

Frequently Paired With Found in 3 installations

These devices are commonly found together in the same smart home setup based on anonymous telemetry data.

Shelly 1PM Mini Gen4 Shelly

3 shared 100% of installs

YS1606-UC t0bst4r

2 shared 66.7% of installs

Shelly 1PM Gen4 Shelly

2 shared 66.7% of installs

Endpoints by Version

Hardware: 9.0

SW: 9.3.2 Latest Seen 4 endpoints

Endpoint 0

Device Types

Server Clusters (hover for details)✓ Rich data

Endpoint 1

Device Types

Server Clusters (hover for details)✓ Rich data

Endpoint 2

Device Types

Server Clusters (hover for details)✓ Rich data

Endpoint 3

Device Types

Server Clusters (hover for details)✓ Rich data

Known Versions

Hardware Version	Software Version	Count	First Seen	Last Seen
9.0	9.3.2	37	2026-05-10 05:28:24	2026-06-12 01:30:49

« Back to device index

Smart Wi-Fi Thermostat (PID 0xE002)

What This Device Can Do

What you can do:

Information available:

Enabled features:

Information available:

Information available:

What you can do:

Information available:

Enabled features:

Setup & Reset Info

Technical Details For developers

Device Compatibility

Thermostat (3 devices)

Relative Humidity Measurement (1 device)

Temperature Measurement (3 devices)

Spec Compliance & Feature Analysis

Frequently Paired With Found in 3 installations

Endpoints by Version

Hardware: 9.0

Endpoint 0

Descriptor

Access Control

Basic Information

Localization Configuration

General Commissioning

Network Commissioning

Diagnostic Logs

General Diagnostics

Wi-Fi Network Diagnostics

Administrator Commissioning

Operational Credentials

Group Key Management

Fixed Label

User Label

Endpoint 1

Identify

Groups

Descriptor

Thermostat

Thermostat User Interface Configuration

Endpoint 2

Identify

Descriptor

Relative Humidity Measurement

Endpoint 3

Identify

Descriptor

Temperature Measurement

Known Versions